PT2272 PDF

  • No Comments

The PTM4 (Rx) receiver module is designed to be used in conjunction with the PT (Tx) transmitter module (Item HCMODU). When used together. PT PT is a Remote Control Decoder Paired With PT Utilizing CMOS Technology.. is a remote control decoder paired with PT utilizing. PTL4 PT is a Remote Control Decoder Paired With PT Utilizing CMOS Technology.. is a remote control decoder paired with PT utilizing.

Author: Tygojora Faujind
Country: Senegal
Language: English (Spanish)
Genre: Career
Published (Last): 28 June 2008
Pages: 100
PDF File Size: 2.76 Mb
ePub File Size: 17.6 Mb
ISBN: 355-1-52194-133-4
Downloads: 87045
Price: Free* [*Free Regsitration Required]
Uploader: Arashiran

If you solder it with “H”, it means high. The pins only go high when a button is pressed. PTM4 data received flow char Click to Enlarge. June 29, at 3: ASK Transmitter input pt22272 WirelessRemote Control. Hi all, Please continue discuss in technical forum.

Remote Control 315MHz by using RF remote control Encoder and Decoder

February 26, at 4: The video on how the RF modules functioning was shared at the end of this tutorial. PT has a maximum of 12 bits of tri-state address pins providing toor address codes; thereby, pt272 reducing any code collision and unauthorized code scanning possibilities.

March 11, at December 9, at June 14, at 6: This IC has Latch or Momentary output type. Direct contact of pt2227. Could you do me a favor to forward this email to your purchasing department or your company CEO? When the A button is released, the matching pin goes low.

  KID65004AF DATASHEET PDF

On the right of the top row there marked pt22272 “L”, where means this row is connected to GND. December 6, at 1: It has 12 bits of tri-state address pins providing a maximum ofor address codes; thereby, drastically reducing any code collision and unauthorized code scanning possibilities. Your site is very interesting. Now depending upon the type of application, the RF module is chosen.

RF Decoder – PT – Mhz [] : Sunrom Electronics/Technologies

Can somebody advise me to resolve this? And the “H” means they are connceted with positive power supply. November 29, at The corresponding Led will light up and switch on the relay. After soldering the circuit, connect the fluorescent lamps and the plug top to the 3 pins terminal block as shown as the below.

PT2272 – PT2272 Remote Control Decoder Datasheet

November 12, at 6: I would try to modify a wireless bell, to make p2272 garage opener, and of course a controller for light in house.

April 23, at 3: Thank you very much. The IC operations was shown by the flow chart at the below. If pr2272 address bits was not match the data will only be received by PT if the button was being pressed and did not released at the transmitter boardthis IC will remain in stand by mode.

So it has valid address. If you solder the address pin with the “L”, it means you set the pin to low. I have 8 ch remote using pt and ptm receiver respectively. This is the reason I would think the momentary receiver type will be appropriate to be connected each to float switch, so that I would expect to have 8 level reading from the tank wirelessly.

  AUTOLESIONES EN ADOLESCENTES PDF

Add a simple wireless control to a device, no addressing, no programming — used a MHz remote with this receiver and you have wireless control up to meters away under ideal conditions!

December 31, p2t272 August 26, at April 15, at 7: Hope can get your explanation. How abt security in this encoder?

Leave a comment Cancel reply. Press the push button on the RF-TX board and observed the result obtained. January 18, at 1: The Led and the relay will be switch off.

Remote Control MHz by using RF remote control Encoder and Decoder – Tutorial by Cytron

In this tutorial, only 2 fluorescent lamps were using. April 3, at 2: Please continue discuss in technical forum. We generally use the 8-bit address code and 4-bit data code.

This makes them suitable for remote control applications, as in where you need to control some machines or robots without getting in touch with them may be due to various reasons like safety, etc. April 24, at September 3, at 6: February 25, at So before we use them, we have to set their adresses ph2272 same.

Posted in : Sex