His house was raided by BATF. After his arrest, Maadi-Griffin lost all ability to sell firearms, but continued to operate for a while, selling plan books and sabots. Maadigriffin Cal Rifle Plans. Last Updated on Thu, 11 Oct | Maadi Griffin 50 Cal. Maadi Cal Kit. Written, Published and Totally Owned by JNS Supply. Last Updated on Mon, 17 Jun | Maadi Griffin 50 Cal. Material carbon steel 3 /4″ square tubing, 5 7/8″ long Three slots on each side” wide, 1 ” long.
It will put marks on the ring, that is ok, they can be sanded off later As the locking ring is being tightened, be sure that the barrel does not move or tighten any more.
Put the bolt cap back on the bolt, and take a new manufactured not reloaded live 50 cal round and insert it into the boltface shell holder, and insert the bolt into the receiver and push the bolt handle down. Conaruct the collar so that it can be inserted into plana back plate planw the brake. The edges must be beveled, aligned, and then weld together and grinc off for a smooth finish.
It must be understood that any construction or attempted construction of any item listed in this book is totally at your own risk. First, put the receiver in a bench vice, wrapped in denim cloth to keep oiF vice marks atuate the receiver so that the bolt handle can be moved freely Remove the bolt, remove the firing pin from tite bolt.
Now, lift the bolt handle and remove the 50 cal unfired round. Dont forget too that youll need a few extra tools for other jobs around the house.
Maadi Griffin Rifle Parts List – Maadi Griffin 50 Cal Rifle Plans
Or to the muzzle end of the barrel 89 ill; The hole in the muzzle brake is. Nor will either company be held liaMc for any loss of any kind. A muzzle brake is affixed to the barrel. Maad, grind down the weld cosmetically and polish smooth. Bend it into a square “U” shape like the trigger spr ing, insert a piece of drill rod into the sear hole anil place the wire h tl groove as shown.
With a little plwns, insert the spring tails and the head of the sear into the back of the bar as shown here. The spacer spring for the link goes in like this Use the hanger wire tools to align and pin the spacer and the link together.
See the drawing, the line with a star at each end. Check the bolt handle, up and down for that slight “feel” of resistance. That will become the pin when trimmed off.
When the link is near the hole, use the hanger wire tool to hold the link you install the trigger shown while The spacer spnng for the naadi goes in like this Use the hanger wire tools to align and pin the spacer and the link together. Make sure that the bolt handle goes up and down easily.
Maadi-Griffin 50 Cal. Rifle Plans
Major Rifle Components 4. Dont forget too that youll need a few extra tools for other jobs around the house. Reset the sear on the link by raising the sear up and moving the link back to contact the sear.
This is a special cast A-3S6 Aircraft abminura handle I: Saew the locking ring up on the barrel, screw the barrel into the receiver plwns it is just snug tight against the 50 cal.
Ep – Maadi Griffin 50 Cal Rifle Plans – Bev Fitchett’s Guns Magazine
Back off the locking ring ail the way forward on the barrel. Next will be a practice run. I ben pkice the holt cap on top of the end oft he lli’ina pm. Be sure the locking ring is all the way forward. Now clieck it out Push down of the sear with your thumb, and pull the trigger with your and the sear will drop Hold the sear down, release the trigger first, then release the sear. Copies of this publication are sold and distributed for mformation purposes only.
This is the res! Screw in the barrel until that “snug” feel, not tight, but snug, as the barrel contacts the round.
Grind off the marks that stand up. Much of the design is similar to the single-shot models, but the magazine is a detachable side-mounted left-side only unit in bullpup configuration and a gas system allows for semi-automatic fire.
These two pieces can be later rewelded together a tier the milling is complete. Screw the barrel into the receiver until it “stops” do not use force just hand snug, then screw the lock ring to the receiver, while checking the bolt handle, when the lock ring is snug, quickly remove the GO-GAGE and replace it with the NO-GO GAGE and the handle should not go down.
Insert the bolt and push the bolt handle down Ifyou have trouble at any stage of construction, call the Hot-Line for assistance. Due to the fact that Maadi-Griffin Co. The large trigger guard and lpans bipod forms a three-point tripod, improving stability.
Stewart, a devout Mormon, named his weapons Maadi-Griffin in reference to the mythical creature of the same name.