Intercure Primer by International Paint – INTERCURE HS BUFF, VPN: EPA/5/A for only $ Buy online or find out more at Richmond Industrial . Intercure can also be used as a primer for substrates other than blasted steel , e.g. stainless steel, alloys etc. Consult International Protective Coatings for. Product Description. Intercure is an epoxy rich zinc phosphate/micaceous iron oxide primer. Key Features: Rapid cure & recoat capabilities in low.
Intercure is not intended for use as a primer for steelwork which may be subjected to immersion conditions.
Typical Coverage per coat 8. Send us your question.
Surface preparation All surfaces to be coated should be clean, dry and free from contamination. Work stoppages Do not allow material to remain in hoses, gun or intercurr equipment. Intercure HS is not intended for use as a primer for steelwork which may be subjected to continuous immersion conditions. Absolute measured adhesion of topcoats to aged Intercure HS is less than that to fresh material, however, it is adequate for the specified end use. This product is not available in pale and pastel shades due to a tendency to discolour rapidly.
Systems compatibility Intercure HS will normally be applied to suitably prepared steel, e.
Please ensure you refer to all datasheets for full application information. However, if necessary, application over prefabrication blast primers can be performed. Suitable for overcoating within 7 hours in most climatic conditions hence speeding up production and throughput in fabrication shops. This product is no longer in stock.
Excessive over application of material on areas such as poorly prepared welds may result in long term stress cracking and so early failure. Consult International Protective Coatings for further details.
Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. As a primer for steelwork intended for use in a wide range of aggressive environments, including offshore, chemical and petrochemical plants, interxure buildings, pulp and paper mills, power plants and bridges.
It is your responsibility to read the Product Data Sheets available below before you place an order and prior to application of the product. The content of this website is our intercuee recommendation and is not advice. The use of alternative thinners, particularly those containing ketones, can severely intercurw the curing mechanism of the coating. The minimum purchase order quantity for the product is 1. VOC values are typical and are provided for guidance purpose only.
This product is no longer in stock Grey.
International Intercure 200 Epoxy Primer
A high solids, low VOC product. To find out more about producing specifications for building projects visit www. Formulated on proprietary polymer technology, which provides rapid cure and overcoating even under low temperature conditions. Consult InternationalProtective Coatings for further details. Over-application of Intercure HS will extend both kntercure minimum overcoating periods and handling times, and may be detrimental to long term overcoating properties.
As a primer for steelwork intended for use in a wide intercude of environmental conditions including offshore, chemical and petrochemical plants, industrial buildings, pulp and paper mills, power plants and bridges.
INTERCURE HS – SAND (KIT / 4G) – L
I would like to hear about offers and services: Please note that NBS product guidance is not a replacement for the manufacturer’s literature and it is recommended that International Paint Ltd be consulted before specifying.
Additionally, in common with all epoxies Intercure HS will chalk on exterior exposure. Inercure question has been correctly sent. The figures stated above are approximate.
INTERCURE 200HS – SAND (KIT / 4G) – 11.36L
Intercure HS is suitable for application to blast cleaned surfaces which were initially to the above standard inrercure have been allowed to deteriorate under good shop conditions for up to days. Thoroughly flush all equipment with International GTA Mouse over image to zoom. The surface may deteriorate to Sa2 standard but must be free from loose powdery deposits.
Your browser does not support automatic copy to clipboard. However, if necessary, application over prefabrication blast primers can be performed. Typical Coverage per coat.
Intercure® – International Paint Ltd
Interzinc 22 mist coat or tie coat may be required. However, these phenomena are not detrimental to anti-corrosive performance. Provides quick cure even at low temperatures often encountered in maintenance painting.