FRITZEL FB33 PDF

  • No Comments

Fritzel FB HF Beam. Read more.. Availability: Out of stock. Backorder possible . € This is not a stock item. Please send an email for expected delivery. Bei den Maßabweichungen schreibt Fritzel Elementlänge ±10mm und bei Abständen ±50mm ohne praktische Beam ist von FB FRITZEL FB Specifications, electrical, 20m-Band, 15m-Band, 10m-Band. Elements, active in band number, 3, 3, 3. Boom Length active for band in use λ.

Author: Mirg Dashura
Country: Uruguay
Language: English (Spanish)
Genre: Life
Published (Last): 14 May 2013
Pages: 391
PDF File Size: 16.72 Mb
ePub File Size: 19.55 Mb
ISBN: 722-2-61386-516-2
Downloads: 36011
Price: Free* [*Free Regsitration Required]
Uploader: Shakasa

The rivets replaced by stainless steel bolt and nut. Till then I was quite happy with the beam. My more than 35 years old Fritzel antenna elements look new after a thorough maintenance. If that process has taken a long time it may be difficult to push the trap out of the case.

Vice versa with the longer traps as used for the 40 meter band length 45 cm I have observed which the tube aren’t round but are oval. In Fritzel specified his antennas and traps for an PA input!

When the antenna is remounted you’re not the first to discover that the SWR is poor due to a wrong installed trap. StrahlerReflektorAbstandalles mm ich habe keine 7,80 hier in den Unterlagen. The FB33 has got a much larger bandwidth and even after 10 years this beam works without any problem. Because of the lenght of the driven element which went from almost 27ft to abt 39ft for 40 mtrs I changed the element to the 30 mtr band.

Oxidation created pits and bumps on the elements. Even a treatment with silicone spray works preservative on the coils and antenna rods. On top I had the old 4 element 50 MHz antenna. It may be removed with thinner. Aber vielleicht hat ja noch einer hier die vom FB33!? Where to put them: His company produced many types of antennas and later then they made antennas for more power. Remove oxidation, dirt and apply silicone grease as a protection to. The resonance’s are respectively Rain and snow does not affect the SWR.

  ELECTRONICA INDUSTRIAL MODERNA TIMOTHY MALONEY PDF

The thickest aluminium rod in the new model has a diameter of 28 mm. Drilling of the rivet and replaced by screw or bolt with nut is than the only cure.

A couple of days later I bought a 24 feet 8 meter antenna tower with a manual hand winch to raise and lower it. I used it on quads overe there and it was wonderful. The resonance’s are not so far apart.

Fritzel FB-33

This can be the reason for future failure or reduced efficiency. Apart from the permanent damage caused to the hot toroid, the shell partially melted and changed shape. Drilling of the rivets and replaced by stainless steel bolts and nuts is the surest way to be spared from future malfunction of the traps.

Fritzel model 83 trap, Bottom: With my call they offend other radio amateurs and people and accuse them of several things.

Amateurfunk Forum • Elementabstände Fritzel FB33

Die Abmessungen der verschiedenen Versionen sind hier zu finden: By first removing the burned part with a cutter, ON4LN successfully restored a staircase with two-component epoxy. The contact is apparently sufficient for the current through 15 m coil for the 20 m band frtizel, but insufficient as parallel circuit trap for the 15 m band.

Email Subscription You are not subscribed to this review. Very soon the 13 element beam came up for MHz and also one for 70 cm, a 21 element, also from Tonna and several other antennas for different bands. This wire is a wire antenna guys dream. If you want friyzel buy something 2nd hand, look at the size of the traps, the diameter of the tubes and the version of the balun. ON4LN wrote to me: FB33 Direktor ist nicht beschrieben, sorry 73 Peter.

Three antennes were no problem for the stronger built tower but for my neighbours it was a ugly sight. I decided to put one steel pipe with the Yaesu rotor at the far side of the house, nearby the shack with one on dritzel to reach a height of 30 ft.

  KEUZEGIDS UNIVERSITEITEN PDF

This lightweight square tower went down with the antennas fbb33 a light storm during the evening of December 28th in Contact the site with comments or questions.

Assembling is much easier, because the holes are drilled and everything is fixed with screws. At this moment they have decided that the SteppIR is an excessive antenna and I may be forced to remove it and get me a smaller antenna name one that does 6 to 40 mtr with a smaller diameter or surface! For an antenna which has been in operation for close to 30 years, the wear and tear is negligible; proof of good workmanship.

Amateurfunk Forum – Archiv

Erhebung von Zugriffsdaten und Logfiles Wir, bzw. These messages are Read More The are suited for the present 5 cm diameter traps and with a punch I made an appropriate hole in the centre. I have not yet tried, but maybe it goes better with a spray of WD40 or Ballistol oil. Shrink tubing as cover cap for 40 mm diameter traps. The 10 m traps of both antennas were identical in terms of construction, etc.

In principle, a trap is a capacitance in parallel with a coil. It was about 10 years old when I bought it and it replaced the Cushcraft A3S. On top I put the small vertical for VHF and in the middle the U-shaped aluminum tube for both the beams. The balun and all traps are still ok after all these years.

This PDF file contains the most recent sizes of radiator, director, reflector and mounting examples.