FLUKE MICROSCANNER2 MANUAL PDF

  • No Comments

get started using the tester. For additional information, see the MicroScanner2 Cable Verifier. Users Manual on the Fluke Networks website. Safety. Warning. MicroScanner2 Cable Verifier. Accessing the Users Manual. This guide provides basic information to help you get started using the tester. For additional. View and Download Fluke MicroScanner 2 user manual online. Cable Verifier. MicroScanner 2 Test Equipment pdf manual download.

Author: Tokus Kagazahn
Country: Congo
Language: English (Spanish)
Genre: Automotive
Published (Last): 26 April 2008
Pages: 91
PDF File Size: 15.81 Mb
ePub File Size: 8.73 Mb
ISBN: 980-8-98204-762-9
Downloads: 98137
Price: Free* [*Free Regsitration Required]
Uploader: Mikasa

Notes If you cannot locate the IntelliTone signal on 2-conductor cables, the cable may be shorted. The digital IntelliTone signal is easier to detect at a distance than analog tones, and its frequency and encoding eliminate cable misidentification due to signal bleed and radiated or ambient noise. It has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15, Subpart J of the FCC rules, which are designed to provide reasonable protection against such interference Integrity Networks Alaska Branch.

Use the probe to find the general location of the tone at a cable rack, patch panel, or behind a wall, as shown in Figure 2.

Using The Toner Refer to Figures 24 and Press PORT to select twisted pair or coaxial cable. Clean the display with glass cleaner and a soft, lint-free cloth. Skip to main content. Punch Down Tools and Termination Mmicroscanner2.

  ELHEDDAF JOURNAL ALGERIEN PDF

Press PORT to select twisted pair or coaxial cabling. Don’t show me this message again. MicroScanner Cable Verifier Users Manual split pair, 15 telephone voltages, 16 —U— universal adapter, 10 —V— version information, 41 voltage detection, 5, 16 —W— wiremap adapter, Test connectors F-connector for coaxial cable.

Microscannfr2 exposure to chemicals appear.

MicroScanner2 Getting Started Guide, Rev. 1 | Fluke Networks

The cable length is Connect the tester to the cable. Page 60 MicroScanner Cable Verifier Users Manual split pair, 15 telephone voltages, 16 —U— universal adapter, 10 —V— version information, 41 voltage detection, 5, 16 —W— wiremap adapter, Telephone cables wired in a star topology Figure 16 are manuap together at a bridge tap at the distribution If you connect the tester to the bridge tap, the tester center.

Only the first bridge tap detected is reported. Got it, continue to dluke. Index cable tests Symbols coaxial cabling, 28 “? Diagnosing Wiremap Faults Appendix A lists the typical causes of wiremap failures.

Use the tester to check for shorts.

Connect the tester and probe to the cabling as shown in Figure 4. For cabling not terminated with an F-connector, use an adapter or hybrid patch cord to connect to the cabling.

  ALPINE CDA-9811 MANUAL PDF

Toning in IntelliTone™ Mode – MicroScanner2

Navigates through screens and changes settings. Connect the tester to the cable.

SmartTone works with the IntelliTone probe and with analog probes. Refer to Figures 24 and Category 8 Cable Testing.

Use the probe to isolate the tone source in the cable bundle or at imcroscanner2 patch panel. Adrian Young Creation Date: This crossed pair is likely caused by mixing A and B cabling.

Specifications Specifications Specifications Specifications apply at 23 C 73 Funless otherwise noted. The display shows the song number 3. Fluke Networks does not warrant that software will be error free or operate without interruption.

Specifications Specifications Specifications apply at 23 C 73 Funless otherwise noted. The display shows the song number 4. Using manuzl Toner You can use the tester with an optional tone probe to locate cables in bundles, at patch panels, or behind walls. IntelliTone mode is indicated by IntelliTone and a scrolling pattern of 1s and 0s on the display.