Dome Camera Installation Manual Weatherproof and Indoor versions www. Contents Introduction. Menu System Manual. Page 4 of 1. THE DENNARD TYPE DOME CAMERA. The Dennard Dome Camera is a precision unit, offering a wide. The Dedicated Micros Camera has a number of features which can be selected by the System. Supervisor when the dome is installed. Any of these can be.
Page 14 Secure the mounting disc with 4 x supplied off M6 socket button head fixings D. Cut or drill a hole in the tile in the required position using the pattern shown below. Safety Bond – Weatherproof Dome Attach safety bond to a suitable secure position in the ceiling void.
Always support dome with bond prior to mating connector. Fasten the dome to the mounting ring B using the provided 3 x No. Mounting brackets may have been ordered and delivered separately. Create an account or sign in to comment You need to be a member in order to leave a comment Create an account Sign up eennard a new account in our community. Ensure power is OFF before connecting the dome.
Dennard Dedicated Micros 2060 D PTZ Dome Camera CCTV
Framing the desired camera image will be easier using a dennarrd monitor. Cut or drill a hole in the ceiling in the required position using the pattern shown below. Dedicated Micros range extended to include a new indoor dome. Such 22060 is indicative that this system dennxrd the following technical standards.
Page 26 Termination All Dedicated Micros domes are fitted with a termination switch, shown above. Control up the coax – This is most likely due to too much or too little video gain. Check the DVR is set to use the correct telemetry protocol and address settings. Offer the bracket base casting into position and fasten to the wall using appropriate fixings.
Sign up for a new account in our community. To Frame the image from a Fixed attitude camera; 1. Up the Coax Configuration Switch settings The switches are color coded, blue and yellow, and are located inside the dome camera housing. Page 32 – Dm fixed attitude dome camera – ‘zo Ceiling installation is made easier by removing an adjacent ceiling tile during installation. The switches are factory set to FD DM up the coax control.
The external camera is weatherproof IP rated. Operating Temp o C: Posted April 3, Remove the selected tile that will have the dome mounted to it. This will provide a dwnnard improvement in camera performance at both the dsnnard and telephoto end of the lens zoom range. Attach the mounting disc A to the dome in the chosen position and use 3 of the existing M4 dome hd screws to attach the hemisphere to the dome.
To use the table; 1. Introduction Introduction The Dedicated Micros camera is a precision unit, offering a cennard variable speed range, together with a large pre-set memory for positions, tours and alarm responses. OK, I have completely refurbished the dome housings and finally got around to testing the setup but I cannot seem to get any vennard from the cameras. Use only with the brackets or equipment specified by the manufacturer. The desired protocol and the node address for the dome are selected by the two rotary hex switches blue and yellow inside the dome.
Dedicated Micros 2060 Installation Manual
Secure the mounting disc with 4 x supplied off M6 socket button head fixings D. Use the serial port connection if serial telemetry is required. I have fitted a BNC connector to the pigtail from the camera for UTC controlattached to the controller and patched to the monitor but I get no picture and cannot see 2006 activity from the dome when I select the camera and move the joystick.
Sign In Sign Up. Register a new account. This lead should be connected to the boxed P.
DEDICATED MICROS INSTALLATION MANUAL Pdf Download.
The switch settings for the protocols and node addresses are shown in the table below. Dedicated Micros Dennard P.
Ceiling Mounting – Weatherproof Dome Attach the mounting disc B to the ceiling in the chosen position and fix 4x M6x16 socket head cap screws supplied into the bushes C as shown dennad.
Page 11 C into the keyhole slots on the base of the dome F enclosure. Page of 36 Go. M6x20mm Caphead Screw pass through the keyhole slots. Software Version The single letter in the middle of the reference indicates the supported camera, refer to the table below for more information.
Locate SW3 on the main PCB adjacent to the mounted connector attaching the daughter board housing the yellow and blue address switches. Always support dome with bond prior dennare mating connector. Snap fit the tile mount bezel E.
Table Of Contents Troubleshooting Secure and hang the dome to a suitable mounting point in the ceiling void by attaching the safety bond spring clip to the eyelet through the large centre hole in the tile.
Open the Technician Menu see Operation and Programming manual for details on accessing the menu. Fit the supplied safety bond E to an attachment point in the ceiling. Hi, I am completely new to cctv, in fact I am installing a setup at my home, I am not a professional installer or anything like dennxrd so please forgive my lack of technical knowledge.