DATASHEET OF HT12D PDF

  • No Comments

HT12D 2 12 Series of Decoders Features. Operating voltage: V~12V Low power and high noise immunity CMOS Built-in oscillator needs only 5% resistor. HT12DDIP Ic-remote Control Decoder Features. Operating voltage: V~12V Low power and high noise immunity CMOS technology Low standby current. IC HT12D can be used only with its pair HT12E. These two ICs together form an Encoder and Decoder pair. They are bit.

Author: Mall Gagar
Country: India
Language: English (Spanish)
Genre: Automotive
Published (Last): 15 August 2013
Pages: 383
PDF File Size: 10.6 Mb
ePub File Size: 3.62 Mb
ISBN: 128-3-82125-456-1
Downloads: 18454
Price: Free* [*Free Regsitration Required]
Uploader: Arashigul

This site uses cookies. Basically found in applications of remote control systems. Interface SD Card with Arduino. Valid transmission; active high. The 4-bit data that is received can be obtained on pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7.

To find out more, including how to control cookies, see here: SPI Module of Arduino. TL — Programmable Reference Voltage. It is mainly provided to interface RF and infrared circuits. Gone are the days when we used to use wires to connect two devices to establish a communication path.

HT12D Decoder IC

This pin will go high when a data is received. After one complete cycle of data transfer the pin TE goes datashwet high impedance state, thus indicating 1 cycle of data transfer. These two ICs together form an Encoder and Decoder pair.

Skip to content Gone are the days when we used to use wires to connect two devices to establish a communication path. So out of vatasheet bits 8-bits will be used to set address and the remaining 4-bit will be th12d to transmit data. Connected to the Ground of circuit. They can also be connected to LED to physically view the received data. This pin powers the IC should use only 5V. A valid transmission in indicated by a high signal at VT pin.

  DICCIONARIO FILOSOFICO DE ROSENTAL PDF

This series of decoders are mainly used for remote control system applications, like burglar alarm, car door controller, security system etc. This oscillator can be used by connecting these two pins h12d a 1M Resistor 17 Valid Transmission VT This pin will go high when pf data is received.

In additional to itit also has 8 address lines which can generally be grounded along with the pin number 9. We should set the bits in same pattern on Encoder and Decoder IC to pair them. Submitted by admin on 27 October This pin outputs hy12d parallel data serially. Skip to main content. Choosing Battery for Robots. This IC hasmany applications in short range remote controlling. The IC is should be powered by 5V pin 18 and the ground pin pin 9 is grounded. This is an CMOS logic integrated circuit encoder.

It is very important that your Decoder should have the same address of that of the encoder. This high-density System-in-Package SiP integrates controller, power switches, and support components.

If any valid data is received they can be obtained from these four pins. This oscillator can be used by connecting these two pins through a 1M Resistor. By continuing to use this website, you agree to their use. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you. Used for interfacing RF circuits generally MegaHz. The data on 4 bit latch type output pins remain unchanged until new is received.

  JUAN FRANCISCO MANZANO AUTOBIOGRAPHY OF A SLAVE PDF

The input data code is decoded when no error or unmatched codes are found. In simple terms, HT12D converts the serial input into parallel outputs.

Thus this helps in setting up oscillations in the IC. If you want security you can connect any of the 8 pins to 5V to make it high.

These are the 8-bit address bits, which is used to protect your data. These pins are generally shorted by a resistor.

HT12D RF Decoder IC Pinout, Details, Equivalent & Datasheet

Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc. For decoding a data the IC will requires an oscillatorluckily this IC has one in-built.

An LED dataxheet also be connected across this terminal to indicate output.

Choosing Motor For Robots.