CONTACTLESS DIGITAL TACHOMETER PDF

  • No Comments

Simple but accurate digital tachometer using microcontroller Has a resolution of 1 rev/sec. The tachometer use an optical pickup scheme for picking . Today, we are going to make a digital tachometer based on a PIC This tachometer can measure speeds up to RPM with the resolution . Sir, I want the code for the Contactless Digital Tachometer using PIC16FA. Abstract: This paper proposes a hardware design of an. “Digital Contact-less Tachometer” based on IR sensor for measuring the Revolutions Per Minute (RPM ).

Author: Bagrel Voodoolkree
Country: Burma
Language: English (Spanish)
Genre: Life
Published (Last): 22 May 2015
Pages: 210
PDF File Size: 18.65 Mb
ePub File Size: 2.46 Mb
ISBN: 207-1-47321-161-6
Downloads: 47498
Price: Free* [*Free Regsitration Required]
Uploader: Meztishicage

You have to test and calibrate your sensors based on application. Can you Provide an lcd version of it please! Previous post Next post. Voltmeter using Transistor intercom circuit. The program actually counts the number of negative going pulses in 1.

C remotes use IR sensors to operate. Dear Sir, Kindly provide C code for better understanding. Can this circuit be purchased on this site? For this setup and every other setup based on principle of reflection of light the IR LED and tachometed photo-sensor are placed side-by-side at a distance of mm from each other facing the obstruction which is generally less than 10cm away from the tip of IR LED.

From the above two graphs you can see that the negative going edge of the waveform indicates the passage of the reflective patch across the sensor and that means one revolution.

  A CIEN MILLAS DE MANHATTAN PDF

Contactless digital tachometer using 3 digit display and measures upto rev/sec

For sending the light across directly max distance is about 10m or more with a very high sensitivity photo detector and digitak intensity IR LED. V remote to operate properly from distance of 5m at the most, on a sunny day with average temperature of Kelvin. This is done just because to save my time but not a text book method. I have tested my T. Only one opamp inside the quad LM is used here and it tachometre wired as a comparator with reference voltage set at 3.

The job of this comparator unit is to convert the spiky collector wave form into a neat square pulse train so that it can tachometeer applied to the microcontroller. Digital tachometer using admin April 20, 39 Comments.

What is the use of burner circuit of microcontroller in this device? Contactlrss circuit diagram of the digital tachometer is shown below. You can use any single supply opamp that matches our supply voltage 5V.

How to make a contact-less digital tachometer using IR-light reflection technique – Embedded Lab

When viewed through an oscilloscope the collector waveform of the photo transistor Q4 2N would look like this:. The circuit diagram of the LCD tachometer using is given below. Next part is the signal conditioning unit based on the opamp LM IC1. Timer 1 is configured as an 8 bit auto reload counter for registering the number of incoming zero going pulses and Timer0 is configured as a 16 bit timer which rachometer the necessary 1 second time span for the Timer1 to count.

  LG SV IG5A PDF

Interfacing Nokia Display to Micro Controller Moisture sensing automatic plant watering system using This is for my study and teaching the program how to srite Thanks a lot for the Originators.

The user interface for programming the microcontroller comes with idgital ISP module. The instruction CPL A will just complement the digit drive pattern in accumulator so that it becomes suitable for the common anode display.

Digital tachometer using Dual supply opamps configured in single supply mode will not give results like a dedicated single supply opamp in the same situation. We are working on the layout part!

Embedded Lab

But this distance varies according to the climatic conditions in the region and also other devices operating in the area. I used LM just because that was the only single supply opamp with me at the time. I want to ask whether the mechanism in this project counts the pulses for 60 seconds and then display it if so then how to configure to delay time for 60 sec and at the same time count the pulses in that duration?

Heart rate monitor with sms alert.

Thank you for all.