CE Mechanics Of Solids May June Question Paper ANNA UNIVERSITY CIVIL 3RD SEMESTER QUESTION PAPER DETAILS. CE MECHANICS OF SOLIDS APRIL/MAY QUESTION PAPER ANNA UNIVERSITY CIVIL 3RD SEMESTER QUESTION PAPER. Anna University Chennai Question Paper Code: B.E / DEGREE EXAMINATION, Nov / Dec and Jan Third Semester.

What are the formula for finding change in diameter, change in length and change volume of a cylindrical shell subjected to internal fluid pressure p? In a ddition, there solidx a shearing stress of 80 MPa acting normal to the normal stresses.

Derive double integration method for cantilever beam concentrated load at free end.

CE2201 Mechanics of Solids Nov Dec 2012 Question Paper

Find the maximum deflection an d the deflection at the point of application of the couple. Find the diameter and length of the wire. What is Cantilever beam? How to increase the strength of a thin cylinder? Also find iii the increase in the distance between the stoppers if a force of 80 kN is exerted between them.

Disc spring or Belleville mechanicw Find the plane of maximum shear stress and its plane. Determine the diameter of a solid steel shaft which will transmit 90 KW at r.

Maximum permissible shear stress is 50 MPa and shear modules 0. Determine the shearing stress. Propose an alternate rectangular section of the same material so that the maximum shear stress developed is same in both sections.

The compound tube carries an axial load o kN. What are the stresses developed in its wall?

It is subjected to a tensile load of kW along the longitudinal axis and tensile load mechanlcs 7 50 kW and kW as the lateral forces in z and y directions respectively. A T section beam of flange mm x 20 mm and web mm x 25 mm is subjected to a shear force of 50 kN. Where shear stress distribution diagram draw for composite section? If one or both of the end portions are extended beyond the support then it is called over hanging beam.

Such principle is called as principle of super position Each layer of the beam is free to expand or contract independently about the layer, above or below. Calculate the external diameter of the shaft which would satisfy these condition. The length and the internal diameter of the c2e201 are 50 cm and 25cm respectively.

The tube is mm long and is closed by rigid washers, which are fastened by the threads on the steel bolt. SF at any cross section is defined as algebraic sum of all the forces acting either side of beam.

Determine the maximum sh ear stress. What are the different sections in which the shear stress distribution is to be obtained? It is filled with fluid under pressure until is volume increases by 50 cubic centimeters.

CE – Mechanics of Solids Two Mark with Answers ~ Vidyarthiplus (V+) Blog – A Blog for Students

A cantilever beam of length L is subjected to a point load w at the free end. In which beam it occurs? Obtained the deflection under the greater load for the beam shown in fig using the conjugate beam method. What are the formula for finding circumferential stress and longitudinal stress? A laminated wooden beam mm wide and mm deep is made of three mm x 60 mm planks glued toge ther to resist longitudinal shear. If a truss carries inclined loads hinged at one end supported on roller at the other end, the support reaction at the roller support end will be normal.

Find i the principal stresses and orientation of principal planes. What do you mean by shear stress in beams? In the case of triangular section, the shear stress is not max at N A. What are the types of loads? If the axial load is replaced by an axial torque of 8 Nm, obtain the angle of rotation about the coil axis and the axial deflection. The frame are generally supported i on a roller support or ii Meechanics a hinged support. Use moment area method. Some external force is acting on ce201 body, the body tends to deformation.

CE Mechanics of Solids – Lecture Notes – Scan Version

Also calculate change in volume. This is called elastic limit Find the span of the beam.

If the number of member in a frame are more than 2j -3then the frame is know as deficient frame 6. Simply supported beam 3. Define bending moment diagram?