ASTM D4258 PDF

  • No Comments

This standard is issued under the fixed designation D ; the number 1 This practice is under the jurisdiction of ASTM Committee D on Protective. ASTM D Standard Practice for Surface Cleaning Concrete for Coating. ASTM D (Plastic sheet test): Place plastic sheet on concrete stab for 24 hours. o ASTM-D Standard Practice for Surface Cleaning Concrete for.

Author: Gardall Arazragore
Country: Bahrain
Language: English (Spanish)
Genre: Travel
Published (Last): 10 August 2006
Pages: 413
PDF File Size: 12.37 Mb
ePub File Size: 8.8 Mb
ISBN: 385-5-95875-687-4
Downloads: 41029
Price: Free* [*Free Regsitration Required]
Uploader: Mazujind

This standard is not included in any packages. Damaged areas must be repaired with an appropriate patching material. Bare plaster must be cured and hard before application. Ensure that all surface contamination has been removed by washing with an appropriate cleaner. So many corrosion protection lining projects succeed or fail with the quality of the surface preparation achieved before the lining is even installed. Ensure that the surface is clean and free of any loose stucco, and that surface pH is between 6 and 9.

Surface preparation methods as outlined in ASTM D are required if the coating system is incompatible. Be advised that any coatings left on the surface to be painted may compromise the service length of the system. Make sure all spackled nail heads and tape joints are sanded smooth and all dust removed prior to painting. Allow the coating to dry at least one week before testing for adhesion. Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards.

Wood must be clean and dry. Make sure all visible grease, oil, salts, and soluble welding residues have been removed prior to power tool cleaning by the methods outlined in SSPC-SP 1. Tape and cover joints with a joint compound.

ASTM D – 05() – Standard Practice for Surface Cleaning Concrete for Coating

Glossy surfaces should be sanded dull. Dull glossy surfaces prior to painting. Your Alert Profile lists the documents that will be monitored. Caulk should be applied after priming.

  DOA KANZUL ARASH PDF

For concrete and steel substrates, a prepared surface is typically one that is clean, dry, structurally sound, and possesses a certain surface profile—the four pillars of good surface preparation. Exterior composition board siding hardboard must be thoroughly cleaned and primed with an alkyd primer, whether factory primed or unprimed.

Surface must be free of laitance, concrete dust, dirt, form release agents, moisture curing membranes, loose cement, and hardeners. The steps below are provided for assistance in properly preparing various common substrates before coating.

Standards Subsctiption may be the perfect solution. Sand surfaces smooth, taking care to sand with the grain.

Surface Preparation Proper surface preparation can improve the outcome of your coating system. Maintenance painting will frequently not permit or require complete removal of all old coatings prior to repainting. Prime and paint as soon as possible after surface prep. There was so much to do before I ever opened a can of paint. This standard is also available to be included in Standards Subscriptions.

Spackle the drywall defects. If the surface is new, test it for pH, many times the pH may be 10 or higher. Proper surface preparation can improve the outcome of your coating system.

Standard – Standard Practice for Surface Cleaning Concrete for Coating ASTM D –

We have no amendments or corrections for this standard. When weathering is not possible or the surface has been treated with chromates or silicates, first Solvent Clean per SSPC-SP1 and apply a test area, priming as required.

Wipe off the dust. The subject of surface preparation leads me to recall my own home interior painting projects.

D2458 exterior surfaces, spackle with exterior grade compounds. If these requirements are ignored, the lining can delaminate from the substrate or fail to cure properly. All of these steps were important to ensure the paint finish was smooth, uniform in color, c4258 resilient. Method of cleaning steel to remove dirt, oil, grease, loose rust, loose mill scale, and loose paint using water at pressures of 2, to 2, psi at a flow of 4 to 14 gallons per minute.

  ARTLANTIS MANUALE PDF

Conco Paints

Plan accordingly to handle the runoff. When viewed without magnification, a Brush-Off Blast Cleaned surface should be free of any visible grease, oil, dust, dirt, loose mill scale, loose paint, and loose rust.

The room must be ventilated while drying. Store finishing lumber and flooring in dry, warm rooms to prevent absorption of moisture, shrinkage, and roughening of the wood.

Any existing checked or peeling paint should be scraped and sanded to a sound surface. High-pressure water blasting is commonly used to clean substrates.

Check for compatibility by applying a test patch of the recommended coating system, covering at least 2 to 3 square feet. Please first log in with a verified email before subscribing to alerts. Rinse carefully and allow to dry. When viewed without magnification, a metallic surface prepared according to this specification should be free of any visible grease, oil, dust, dirt, mill scale, paint, rust, oxides, corrosion products, and other foreign matter.

Rooms must be heated in cold, damp weather. Make sure all visible grease, oil, salts, and soluble welding residues have been removed before hand tool cleaning by the methods outlined in SSPC-SP 1. To avoid premature lining failures resulting from improper surface preparation, lining specifiers, applicators, and inspectors need to be familiar with these industry standards for surface preparation and to adhere to their principles in practice.

Subscription pricing is determined by: Procedures include broom cleaning, vacuum cleaning, air blast cleaning, water cleaning, detergent water 4d258, and steam cleaning. Following these guidelines will help ensure sufficient adhesion of the coating and can help prolong the life of astn coating system.