AGMA 2015-1-A01 PDF
racy documents correlate as shown in Figure 1. Current Status of New Standards. In late , the new tangential accuracy stan- dard ANSI/AGMA A AGMA A01 (R). Accuracy Classification System – Tangential Measurements for Cylindrical Gears. standard by American Gear. CONTAINS ANSI/AGMA A ACCURACY CLASSIFICATION SYSTEM- TANGENTIAL MEASUREMENTS FOR CYLINDRICAL GEARS AND AGMA.
||15 December 2012
|PDF File Size:
|ePub File Size:
||Free* [*Free Regsitration Required]
Typically, the factor for this adjustment is the cosine of the angle between the normal direction and the specified tolerancing direction. When properly applied, gears manufactured by specific control techniques will be found to be of uniform accuracy.
The measurement of gearing mated in an assembly for a specific application is beyond the scope of this document. Therefore, the users of this standard are cautioned against the direct application of tolerance values to a projected performance of unassembled loose gears when they are assembled. A master gear is a gear of known accuracy, designed specifically to mesh with the gear to be inspected for composite variation.
A New Standard in Gear Inspection
Tolerance values for gears outside the limits stated in this standard should be established by determining the specific application requirements. Add to Alert PDF. Measurements at any other inclination will be larger. For undated references, the latest edition of the referenced document including any amendments applies.
We have no amendments 2015-1-a1 corrections for this standard.
ANSI AGMA A01_百度文库
Single flank composite, tooth–to–tooth cp: It does not necessarily indicate compatible tooth shape for loaded conditions. Need more than one copy? SCOPE This part of ISO establishes a tolerance classification system relevant to manufacturing and conformity assessment of tooth flanks of individual cylindrical involute gears.
During electrical filtering, the test data signal passes from the probe head through an electrical filtering RC circuit and finally on to the data analysis and output devices. The American National Standards Institute does not develop standards and will in no circumstances give an interpretation of any American National Standard. In this standard, lower AGMA accuracy grades designate higher precision in order to be consistent with international standards.
2015-1-a1 particular, the following should be noted: Standards Subsctiption may be the perfect aagma. Master gears shall conform to clause 7 tolerances, for accuracy grade 2, 3 or 4. This has been done for two reasons. This specified direction, called the tolerancing direction, may be normal to that surface, inclined at some angle, or along the arc of a specified circle.
The datum axis determines tooth geometry, thereby being the reference for measurements and associated tolerances. It is developed by subtracting the ordinates of a straight–line gradient from the ordinates of the design profile. Consultant Profile Engineering, Inc. Tolerance formulas were based on the actual gear geometry rather than on geometric mean values. No particular method of measurement or documentation is considered mandatory unless specifically agreed upon between manufacturer and purchaser.
Any person who refers to any AGMA technical publication should be sure that the publication is the latest available from the Association on the subject matter. In such cases, it is possible to modify the accuracy grade to include an accuracy grade for each gear element or composite tolerance. The committee agreed that a new gear classification system was needed: Applicable definitions are provided.
For convenience, some tolerance tables are provided in annex A, and additional tables covering all tolerances, grades, and sizes in both metric and U. Measurements made in the normal direction coincide with agmma direction of tooth meshing motion. The selection of the particul ar method depends on the magnitude of the tolerance, the size of the gear, the production quantities, equipment available, accuracy of gear blanks, and measurement costs.
In both systems, the classes or grades are separated by a square root of 2 stepping factor. A filter that excludes short wavelength high frequency data is called a low-pass filter.
Specifying an AGMA accuracy grade or measurement criteria that requires closer tolerances than required by the application may increase the cost unnecessarily. The system of classifying very accurate gears with a low number, instead of retaining the method of AGMA Users of this standard should assure themselves that they are using the symbols, terminology and definitions in the manner indicated herein.
The variability of the measuring process contributes to the variability of the manufacturing process. FpsT FpT is the tolerance, sector pitch deviation; is the tolerance, total cumulative pitch.
A New Standard in Gear Inspection | Gear Solutions Magazine Your Resource to the Gear Industry
That parameter observes only the deviation in position of the first and last teeth of each sector of k pitches. An example of how to establish an AGMA classification number for a given set of conditions is presented in figure 5.
The following formulas were then developed: Example of statistical process control SPC application. AGMA technical publications are subject to constant improvement, revision, or withdrawal as dictated by experience.
Brad Foote 2015-1-w01 Works, Inc. The matching process for such gears sold as pairs assumes greater importance than the individual absolute measurements. Requests for interpretation of this standard should be addressed to the American Gear Manufacturers Association.