LM396K DATASHEET PDF

  • No Comments

the LM In addition to excellent load and line regulations, the DATA SHEET FOR REFERENCE ONLY. Consult for possible alternate. LMK Datasheet, LMK PDF, LMK Data sheet, LMK manual, LMK pdf, LMK, datenblatt, Electronics LMK, alldatasheet, free, datasheet. LMK datasheet, chip LMK pdf, LMK circuit, ic, LMK, Datasheet search site, Electronic Components and Semiconductors.

Author: Tygokree Shaktirg
Country: Algeria
Language: English (Spanish)
Genre: Travel
Published (Last): 21 May 2012
Pages: 365
PDF File Size: 7.37 Mb
ePub File Size: 15.49 Mb
ISBN: 627-9-78021-171-1
Downloads: 17805
Price: Free* [*Free Regsitration Required]
Uploader: Kazizilkree

National does not assume any responsibility for use of any circuitry described no circuit patent licenses are implied and National reserves the km396k at any time without notice to change said circuitry and specifications.

Although it may not be immediately obvious best load regu- lation is obtained when the top of the divider is connected.

Using lm/ to convert 12v/18a to v/a

LM is specified for a 0 C to. Create a thread in the forum so that other members can benefit from the posted answers. Last edited by deze4; 30th August at Current limit is measured 10 ms after a short is applied to the output DC measurements may differ slightly due to the rapidly changing junction temperature. Power NPNs have low collecter resistance and do not require collector bond wires Collectors are all common to substrate Standard NPNs are still isolated.

The LM is exceptionally easy to use Only two external resistors are used to to set output voltage On-chip adjust- ment of the reference voltage allows a much tighter specifi- cation of output voltage eliminating any need for trimming in most cases The regulator will tolerate an extremely wide range of reactive loads and does not depend on external capacitors for frequency stabilization Heat sink require- ments are much less stringent because overload situations do not have to be accounted for.

If Military Aerospace specified devices are required please contact the National Semiconductor Sales Office Distributors for availability and specifications.

Dropout voltage is input-output lm396o differential measured at a forced reference voltage of 1 15V with a 10A load and is a measurement of the. C3 improves ripple rejection output imped- ance and noise C2 should be 1 mF or larger close to the regulator if C3 datassheet used. Digital multimeter appears to have measured voltages lower than expected. DC regulated output voltage. PNP transistor not working 2. Unless otherwise stated these specifications apply for T.

  ANSI 117.1 PDF

How reliable is it?

Because the LM is a three-terminal device it is not pos- sible to provide true remote load sensing Load regulation will be limited by the resistance of the output pin and the wire connecting the regulator to the load For the data sheet specification regulation is measured 1 4.

Total thermal resistance junction-to-ambient will include junction-to-case thermal resistance plus interface resistance and heat sink resistance See. Using single 12V supply to deliver 12V and 5V Dec 242: ESD rating to be determined. Lead Temperature Soldering 10 seconds. See Curves for Limits. The actual heat sink chosen for the LM will be deter- mined by the worst-case continuous full load current input voltage and maximum ambient temperature Overload or short circuit output conditions do not normally have to be considered when selecting a heat sink because the thermal shutdown built into the LM will protect it under these conditions An exception to this is in situations where the regulator must recover very quickly from overload The LM may take some time to recover to within specified output tolerance following an extended overload if the regu- lator is cooling from thermal shutdown temperature approx- imately to specified operating temperature C or C The procedure for heat sink selection is as follows.

Datasheets search archive of electronic components datasheets

Three-terminal regulators can only provide partial Kelvin load sensing see Load Regulation Full remote sensing can be added by using an external op amp to cancel the effect of voltage drops in the unsensed positive output lead In. Thermal as well as electrical load regulation must be con- sidered with IC lm36k Electrical load regulation occurs in microseconds thermal regulation due to die thermal gra- dients occurs in the 0 2 ms ms time frame and regula- tion due to overall temperature changes in the die occurs over a 20 ms to 20 minute period depending on the time constant of the heat sink used Dtasheet induced load regu- lation is calculated from.

  UNA NOCHE DE VERANO GERRI HILL PDF

Load regulation on the 2-pin package is determined primarily by the xatasheet drop along the output pin Specifications apply for an external Kelvin sense. Choosing IC with EN signal 1. Connected as satasheet Rw is not multiplied by the divider ratio Rw is about 0 X per foot using 16 gauge wire This translates to 40 mV ft at 10A load current so it is important to keep the positive lead between regulator and load as short as possible.

AF modulator in Transmitter what is the A?

LM396K Datasheet

Email cnjwge tevm2 nsc com. Internal current and power limiting. Temperature coefficient of output voltage. Figure 7 the LMA op amp forces the voltage loss. R3 is selected to supply partial load current Therefore a minimum load. A few words of caution 1 R3 power rating must be increased to V.

Nominal line voltage AC rms. ModelSim – How to force a struct type written in SystemVerilog? Dec 248: The factor of 1 1 is only an approximate factor accounting for load regula.

This is a worst-case specification which includes all effects due to input voltage output current temperature and power dissipation Maximum power.

Figure 5b to improve load regula. R3 watts Regulator power dissipa.

The LM will tolerate a wide range of input and output capacitance but long wire runs or small values of output capacitance can sometimes cause problems If an output capacitor is used it should be 1 mF or larger We suggest 10 m. L,396k block is unconnected 3.

Please don’t make requests for help in private using PM.