IC 74LS373 PDF

  • No Comments

74LS, 74LS Datasheet, 74LS Octal D Flip-Flop, buy 74LS, 74LS pdf, ic 74LS These 8-bit registers feature totem-pole 3-STATE outputs designed specifically for driving highly-capacitive or rela- tively low-impedance loads. Operation and working of Latch IC (74LS) Working of Latch IC and operation of Flip flop to perform as buzzer latch IC its.

Author: Tygokazahn Tojabei
Country: Kazakhstan
Language: English (Spanish)
Genre: Automotive
Published (Last): 23 September 2010
Pages: 209
PDF File Size: 11.41 Mb
ePub File Size: 15.56 Mb
ISBN: 816-3-66024-801-4
Downloads: 59424
Price: Free* [*Free Regsitration Required]
Uploader: Zolobar

IC 74LS373, TTL LS series, OCTAL D-TYPE TRANSPARENT LATCHES AND EDGE-TRIGGERED FLIP-FLOPS, DIP20

Problem with 74LS latching! Thanks also for reminder on LED driver, I had dropped down to logic states! The following two tabs change content below. Do I need pull up resistors or does this sound like bad chips. Can anyone please help me sort out the problem?.

Input port and input output port declaration in top module 2. It doesnt latch in HIGH state. Synthesized tuning, Part 2: Results 1 to 20 of What is the function of TR1 in this circuit 3. Frank Donald October 27, 2 Comments. I will get ic’s by day after tomorrow, will try your schematic and update you soon.

[SOLVED] Help with Latch IC 74LS based latching ciruit

Originally Posted by KerimF. The 74ls3773 was powered with 5V power supply and as you can see that the switches were connected directly to the power supply so when the switch is not pressed it gives low signal to the input pins D0-D7. CMOS Technology file 1. The led in the circuit is always Off. The time now is They were a great introduction to simple logic and hardware which is a bit lost in todays massive chips.

  COMPUTER GRAPHICS ZHIGANG XIANG ROY PLASTOCK PDF

The beauty of this simple circuit is it actually debounces your switch, i. Place data on input pin 3 – i.

Quiz Buzzer Circuit using IC 74LS – Gadgetronicx

When the OE pin is low input data will appear in the output. And diodes was used to allow the forward flow of current from the output pins of the IC and thereby switching the transistor ON and thus perform the Latching operation. Help with Latch IC 74LS based latching ciruit I actually made a similar project 74le373 in the 80’s when experimemting with programmable logic the good old days! If you have CD, the remaining 2 gates can be used to combine the 2 switches in one.

PNP transistor not working 2. The current I1, R7 and Q2 replace the push-button switch in order to simulate the circuit. 74sl373 low state in the Oc pin enables the latch of the IC thereby providing continuous high signal in the output pin.

The only potential issue is both switches operating together as the output becomes indeterminate. OE is held tied to ground. Digital multimeter appears to have measured voltages lower than 74sl373.

Frank Donald is an Electronics and Communication Engineer who loves building stuff in his free time. Originally Posted by kripacharya.

Latest posts by Frank Donald see all. The IC 74LS is a transparent latch consists of a eight latches with three state outputs for bus organized systems applications. Distorted Sine output from Transformer 8.

  HANDBOOK OF PSYCHOLOGICAL ASSESSMENT GARY GROTH MARNAT PDF

SCR Silicon Controlled rectifier was connected to the output pins of the IC and along with it diodes are also connected. You people are very helpful, Thanks. The following two tabs change content below. It will be a great mini project to do at you home and i bet you will like it.

How can the power consumption for computing be reduced for energy harvesting? The initial state of the LED is off U3 output is low. Notify of all new follow-up comments Notify of new replies to all my comments.

If you like I will draw kc schematic for you. Here is an example http: In this point of time the IC will lc respond to any of the input signal given by any other switches to it. The switches are given to each participating competitors and the respective bulbs can be placed before them to determine which team pressed the switch first.

Also I may not reply at time. Since the output was latched with the input this circuit eliminate the confusion among the participants and also it provides room for eight teams to play at a time. Frank Donald November 4, 3 Comments. Last edited by sharikbaig; 27th August at