HAMEG HM507 PDF

  • No Comments

Hameg HM Explore Test Equipment on Octopart: the fastest source for datasheets, pricing, specs and availability. Buy Rohde & Schwarz HM Series HM Digital Oscilloscope, Digital Storage, 2 Channels, Hameg 50MHz Analog Digital Oscilloscope HM Data Sheet. Analog Oscilloscope 2 x 40 MHz Hameg CombiScope HM Analog oscilloscope, Analogic oscilloscopes, Cathode rays oscilloscope, Cathode ray.

Author: Kajigore Mikaran
Country: Croatia
Language: English (Spanish)
Genre: Marketing
Published (Last): 10 September 2005
Pages: 391
PDF File Size: 12.62 Mb
ePub File Size: 11.27 Mb
ISBN: 122-1-92344-668-3
Downloads: 99388
Price: Free* [*Free Regsitration Required]
Uploader: Babei

For emission the limits for residential, commercial and light industry are applied. The case, chassis and all measuring terminals are connected to the protective earth contact of the appliance inlet. Only in this way is it largely certain that all signals are displayed with the accuracy on which the technical data are based. Purchase of the new HAMEG scope tester HZ 60, which despite its low price is highly suitable for tasks of this type, is very much recommended. Type of signal voltage Type of signal voltage Voltage values of a sine curve The oscilloscope HM allows examination of DC voltages and most repetitive signals in the frequency range up to at least 40MHz -3dB.

The vertical amplifiers have been designed for minimum overshoot and therefore permit a true signal display. When transmitting square signals with short rise When very fast risetimes are being measured, the risetimes of times, transient phenomena on the edges and top of the signal the oscilloscope amplifier and of the attenuator probe has to be may become visible if the correct termination is not used. Controls and readout B: This can save the purchase of an oscilloscope with larger bandwidth.

Operation of some pushbuttons activates the display of menus. There are Standard and Pulldown Menus.

The latter will be described at the end of the listing. Controls and readout pushbutton underneath the triangle symbols. The DC voltage then instrument setting and return from menu display to can be determined by taking the deflection coefficient, previous mode. Controls and readout Y POS: In and negative peak values. Controls and readout or would be invisible when being set above or below the e.

Controls and readout As long as the pulldown menu is displayed, briefly pressing 4. The last function setting of the TRIG. Controls and readout the knob is rotated clockwise. Hamrg signal sounds on reaching Simultaneously the time value increases and is marked h,507 maximum hold off time. Similarly in the opposite with a minus – sign, as post trigger is condition is direction until minimum hold off time is hakeg HO LED present.

Controls and readout Digital mode. It is recommended to capture and display the signals in Controls and readout Functions coefficient switch to time vernier fine adjustment control and vice versa. Controls and readout readout, between 1: Controls and readout 2 Measuring signal selection trigger source: The measured value is calculated from pulse start. Controls and readout nm507 The Digital mode only.

  HAND BALANCING FOR MUSCULAR DEVELOPMENT BY BILL HINBERN PDF

CURSOR lines must be set to the signal according to the A triangle symbol is automatically positioned on the most selected channel.

Controls and readout CAL. Pressing and holding opens the CAL. Only in chopped DUAL mode can both channels be displayed during one time base sweep.

The software version installed in HO should not be function. By this adjustment, function is active. As long as the HAMEG logo is visible different the capacitive division assumes the same ratio as the ohmic internal checks are made. Operating modes of the vertical amplifiers in Yt mode Connect the Triggering and time base Please note that the Y position settings are also added but are display if the test voltage leads or lags the reference not affected by the invert function.

A CR network before the test haeg input of the oscilloscope can help here.

Triggering and time base Triggering and time base Relatively small phase angles at not too high frequencies can be measured more accurately in the X-Y mode with All controls regarding trigger and time base are located on the Lissajous figures. Triggering and time base Trigger coupling The automatic triggering works above 20Hz.

The failure of automatic triggering at frequencies below 20Hz is abrupt. However, it is not signified by the trigger indicator LED which Instrument specific information regarding this item can be may still be blinking.

Triggering and time base Video signals are triggered in the automatic mode. This also applies within certain limits, to whole number triggering is virtually independent of the display height, but multiples or fractions of the line frequency. Line triggering can the sync pulse must exceed 0. The external trigger voltage may have a completely different form from the test signal voltage, but must be synchronous with the test signal.

Triggering is even possible in certain limits with whole number multiples or fractions of the test frequency. In chopped DUAL mode, using high expansion ratios in If a signal is applied with a pulse duty factor of approx. Testing Capacitors and Inductors capacitors, and inductors. Certain tests can also be made to A horizontal ellipse indicates a high impedance or a relatively integrated circuits. All these components can be tested small capacitance or a relatively high inductance.

A vertical ellipse indicates a low impedance or a relatively large The test principle is fascinatingly simple. HAMEG enables the user to select the most suitable mode for the specific measurement. The sampling rate, which depends on the time base setting, is displayed by the readout.

  FPM WEB DYNPRO ABAP PDF

For a given POS. Each item can be called and causes an automatic adjustment. Baud-Rate Setting A data carrier with programming examples, a command list Page of 44 Go. Table of Contents Add to my manuals Add.

HAMEG HM MANUAL Pdf Download.

General Information General Symbols condition. Warranty Only in this way is it largely certain that all signals are displayed with the accuracy on which the hamegg data are based. Controls And Readout Controls and readout B: Page 12 The latter will be described at the end of the listing. Page 13 Controls and readout pushbutton underneath the triangle symbols.

Page 15 Controls and hamev or would be invisible when being set above or below the e. Page 16 Controls and readout As long as the pulldown menu is displayed, briefly pressing 4.

Hameg HM507 50MHz CombiScope®

Page 18 Controls and readout the knob is rotated clockwise. Page 19 Controls and readout Digital mode.

Page 20 Controls and readout Functions coefficient switch to time vernier fine adjustment control and vice versa. Page 21 Controls and readout readout, between 1: Page 23 Hameb and readout 2 Measuring signal selection trigger source: Page 25 Controls and readout Page 26 Controls and readout CAL. Page 28 Controls and readout First Time Operation By this adjustment, function is active. Adjustment At 1mhz Operating modes of the vertical amplifiers in Yt mode Connect the X-y Operation Triggering and time base Please note that the Y position settings are also added but are display if the test voltage leads or lags the reference not affected by the invert function.

Hameg HM507 Manual

Ahmeg Of An Amplitude Modulation Triggering and time base Triggering and time base Relatively small phase angles at not too high frequencies can be measured more accurately in the X-Y mode with All controls regarding trigger and time base are located on the Lissajous figures. Normal Triggering Triggering and time base Trigger coupling The automatic triggering works above 20Hz. Radom Sampling 25 samples per division. Comments to this Manuals Your Name. Enter text from picture: By pressing ‘print’ button you will print only current page.

To print the manual hameh, please, download it. Don’t show me this message again. Got it, continue to print. Don’t have an account?