ATTANSIC ATTP1 PDF

  • No Comments

, 13, ATTANSIC, -. Kring Electronics Co., Ltd. , -, Attansic, sop8. 63, 0, ATTANSIC, -. Rantle East Electronic. , -, ATTANSIC, SOP. 年12月11日 ATTP1_ – Technology Corporation ATTP1 Over Temperature Please contact Attansic Technology Corp. for the latest documents. Attansic. ATTP1. Tel:. MFG:. ATTANSIC. Picture. D/C:. 09+. QTY:. Packaging:. SOP8L. Package:. Note:. 原装正品. Support. No“ATTP1”Picture.

Author: Dibei Dotilar
Country: Martinique
Language: English (Spanish)
Genre: Medical
Published (Last): 1 July 2013
Pages: 93
PDF File Size: 19.43 Mb
ePub File Size: 5.10 Mb
ISBN: 656-2-96233-492-9
Downloads: 35679
Price: Free* [*Free Regsitration Required]
Uploader: Voodoolkree

However, because of the way the mod is done, the odds of messing it up in such a way that you dissable the OTP function are pretty low. You don’t need to move the jumper though.

ATTP1_1.3.pdf

Where’s the thermal diode? It didn’t change my temp readings at all, but it is theoretically possible for there to be a slight change in the reading. Lift this pin just as you did pin Webb City, Mo Posts: You’ll find that trying to solder the wires to the broken pins, while not impossible, is exceedingly difficult. This means that your poor CPU is going to blow its brains out just as soon as it loses proper cooling for any reason.

Tie the analog voltage supply for the Winbond chip to the 5vsb rail instead of the 5v rail. Solder to pin 61 first, then pin How to test OTP?

NF7-S CPU Thermal Diode Mod, Version – AOA Forums

I find that the edge of a single-edge razor blade works rather well for helping lift this pin while I apply heat with the soldering iron. As for the northbridge, does it have a thermal diode? So what is the solution? Well, I’ve solved that problem. The jumper wire will need to be about 3. In my case, I actually took a chance with my CPU to try it out. Run a jumper from pin 61 of the Winbond chip to pin I’ve personally verified this a few times myself, so I know it works.

  EN 50121-2 PDF

Attansic ATTP1 datasheet & applicatoin notes – Datasheet Archive

I’ve been looking for developer’s docs for the NF2 chipset and haven’t been able to find any. While this mod works pretty well, it has one glaring drawback, which I mentioned in the previous post: I just have you solder directly to the pin agtp1 it is simpler attansoc explain.

As for the other, yes you should solder pin 4 of the Attansic back down to the mobo. Find pin 61 of the Winbond chip. Anything else is nearly impossible. If you muck this up and turn your board into a doorstop, don’t come crying to me. I ahtp1 think it did. When the PSU is shutdown or in standby, this rail is dead, and all of the items connected to the monitor inputs are no longer in a high impedance state.

The original mod involved disabling the Attansic chip protection because simply hooking the thermal diode from the CPU to the Winbond chip would result in the system not powering up, and the familiar two-tone “You’ve got something really mucked up” siren. A fine tip soldering iron is definitely a must. I believe the AN7 has a thermal probe under the north bridge.

This is the analog voltage input. It is more likely that you will mess it up such that the OTP function trips prematurely and you aren’t able to power on the computer at all. If I understand your question attansjc, then to restore the mobo back to default, you simply have to remove the mod.

  ELEMENTS DE SYNTAXE STRUCTURALE TESNIERE PDF

ATTP1 Attansic CPU thermal protection controller chip SOP8

Also note that, because you are now monitoring the thermal diode directly, the thermistor in the socket is now rather pointless. It is the pin at the very top left corner of the Winbond chip on the top, when viewed as described above.

This connects to channel two of the Winbond chip, which means you can now use channel two on pin for something else. BB code is On. If you have previously modded your mobo to read the thermal diode, you MAY find that your temps are degrees higher than they used to be. That is one of the reasons I did it the way I did, so that you could undo it if necessary. You should thread the jumper first, then solder to the Attansic chip, then finally solder to the Winbond chip.

However, be aware that soldering pin 97 and pin back down is rather tricky because of the fine spacing of the pins. It is the 4th pin from the top right corner of the chip going down the right side of the chip, when viewed as described above.