ASTM A ASME SA “Standard Specification for Nickel and Nickel-Base Alloy-Clad Steel. Plate”. “STANDARD SPECIFICATION FOR NICKEL AND. Buy ASTM A SPECIFICATION FOR NICKEL AND NICKEL-BASE ALLOY-CLAD STEEL PLATE from SAI Global. Designation: A − 12Standard Specification for Nickel and Nickel-Base Alloy- Clad Steel Plate1 This standard is issued unde.
Permissible Variations Metric Equivalents in. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.
The reduced section shall have a gradual taper from the ends toward the center, with the ends 0. The surface condition of the repaired area shall be restored to a condition similar to the rest of the 2a65.
ASTM A – 12 Standard Specification for Nickel and Nickel-Base Alloy-Clad Steel Plate
Each specimen shall be in the? The composite plate atm undergo shear strength test, bond strength test, and tension test and shall conform to the required tensile strength and yield strength.
These bend tests shall be made in the manner of the tension tests indicated in Fig. The shear test, when speci?
Several of those considered suitable for use with this speci? When none has been speci?
ASTM A Clad Plate | ASTM A Plate | ASTM A Nickel Coated Plate
Repair of Cladding by Welding A number in parentheses indicates the year of last reapproval. Originally approved in Historical Version s – sstm previous versions of standard. The sides w265 the bend test specimen used for bond strength determination may have the corners rounded to a radius not over 1? For purposes of de?
The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. If the requirements of this speci?
Greater separation shall be cause for rejection. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. The nickel or nickel-base alloy cladding metal shall conform to prescribed chemical composition.
The material shall be cleaned and sufficient asstm taken to represent the full cross-section of the remainder.
The material is generally intended for pressure vessel use but may be used in other structural applications where corrosion resistance of the alloy axtm of prime importance.
Historical Version s – view previous versions of standard Translated Version s: Method of test and acceptance standard shall be as agreed upon between the purchaser and the manufacturer.
ASTM A265 Clad Plate
The tensile properties thus determined shall meet the base steel requirements. NOTE 3—The dimension t is the thickness of the test specimen as provided for in the applicable material speci?
Specify whether applicable to the cladding alloy, backing steel, or both see Section In reducing the thickness of the aastm, both the alloy 3 Metric Equivalents in. The base metal shall conform to the chemical requirements of the speci?
ASTM A265 GR 1 titanium alloy strip sheet plate
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Areas within 1 in. The steel shall be made by the open-hearth, electric furnace with separate degassing and refining optionalor basic-oxygen processes, or by secondary processes whereby steel made from these primary processes is remelted using, but not limited to electroslag remelting or vacuum arc remelting processes. Workmanship Finish, and Appearance General Requirements for Delivery Current edition approved May 1, This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?
This abstract is a brief summary of the referenced standard. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Number of Tests and Retests 8. Product and chemical analyses shall be performed on the cladding alloy and be accomplished by wet chemical or instrumental procedures. Testing for shear strength for clad plates with minimum cladding thickness of 0.
Ultrasonic Examination in accordance with Speci? If wet chemical procedures are used, millings may be taken only when the composite plate thickness is sufficient to permit obtaining millings without danger of contamination from the adjacent layer. The minimum cladding thickness for shear testing shall be 0. Reports shall include the results of ultrasonic inspection when Supplementary Requirement S12 is speci? Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.
Other tests may be performed by agreement between the supplier and the purchaser. Link to Active This link will always route to the current Active version of the standard. The base metal shall be carbon steel or low-alloy steel conforming to the specifications asrm steels for either pressure vessels or for general structural applications. Materials and Manufacture 5.
Such requirements sstm include, but are not limited to the following: ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. If spectrometric procedures are used, the sample shall be exposed on the center line of the cladding when there is sufficient cladding thickness available so that there is no contamination from the adjacent base metal.